$@# Fiberglass Boat Building And DIY Guide &^@!

My dad has an old aluminum boat we use for duck hunting. Its from the early '80's, made by a Central California company called Valco, which is no longer. Its a great size - 12' long and over 50" wide. All the flat-bottom Jon boats made now in 12' are " wide, and really only good for 2 aluminum boats repair 80 and gear, while this one is stable with 3 and a dog, so its worth repairing. Valco boats are like Grumman canoes: thick aluminum made to aircraft specs from when America was Great Before.

I'd aluminum boats repair 80 a riveted Valco or Grumman over a modern "welded" boat made from recycled Bud cans any day. Unfortunately, I don't have any 'before' pics of the whole boat, but from the detail shots it'll be clear it needed a thorough restoration.

I figured the bolts that hold the motor to the transom the stern, reinforced with wood, that outboards are clamped onto were loose, or rusted, or even a little stripped. Turns out, the whole transom was rotten. Not just rotten, it was basically dust and splinters. I have no idea how the motor didn't fall into the water and sink.

As I started removing screws, something funny happened - none of the nuts turned, but ALL of the bolts snapped. Stainless steel rusts like anything else, when its embedded aluminum boats repair 80 rotten wood. So after breaking off all the machine screws and letting the splinters fall out, I knew it was in need of some major surgery. With a closer look, it was clear the plywood seats had also eroded to where they were mostly just sitting on the floatation foam inside the thwarts.

Those would also need to go. These old boats had solid 2-side rivets on the major hull seams, and blind rivets for the corner plates. Almost all of the blind pop rivets were gone, or at least had lost their flanges and had to be punched.

Had to do some clamping and straightening to get them to go into the holes, but didn't want to drill any new holes so aluminum boats repair 80 was worth it. Drift pins FTW! I had to borrow a friend's pressure washer because I don't know where mine is. Probably lent it to someone.

There is probably exactly 1 fewer pressure washers in the world than people who need them, so they all just get passed in an enormous circle. I cleaned the boat inside and out, and took some time spraying hard at the seams to look for leaks.

Didn't find any, but the stern seams that transom again! Since the boat's almost 40 years old, I decided to seal all the seams and rivets. You always want to seal watercraft on the outside. Anything floating is creating some water pressure with its displacement. So if you seal the seams and rivets from the outside, that pressure helps the seals stay on.

If you seal the inside, water will still exist within the seams, and the pressure will always be working to push the seals. I used paint-on Flex Seal as seen on TV!

Paint doesn't stick to aluminum boats repair 80 all that well, but if it gets scratched and exposed, it'll just be more camouflage. I did shoot the flex seal with some Krylon Plastic Primer. It was a guess, and it didn't do. Probably wouldn't bother if I did it. And then I coated the whole bottom with some spray-on pickup truck bedliner. It'll provide some abrasion resistance and protection, and actually reduces drag by breaking up surface tension as the water runs along the hull.

Think golf balls or shark skin. I really only had the square-footage needs for one sheet, but since all 3 seats are 16" aluminum boats repair 80, and 50" long, it wouldn't have left me anything long enough for the 50" wide transom boards.

I made a cardboard template from the old transom. I decided to make it 2" taller than the old one, to give more support to the stern end of the boat. After cutting, I test-fit the seats so I could mark the holes for their new hardware. Didn't want to drill any new holes anywhere if I didn't have to.

I primed and painted both sides of all the pieces of wood, even the sides of the seats which will be hidden. Primer is actually designed to hold onto moisture, which is why it holds paint on. But primed and unpainted wood or anything else is actually worse than leaving it bare. I got the transom bolted in through all the same old holes. Added some stainless fender washers to the middle holes, where the wobbling engine had made the old holes into ovals.

I noticed that the old seats had failed along their ends. The long dimensions rested on aluminum thwarts, but the ends were hung from aluminum flanges. Since we mostly step from the dock onto the ends of the seats, having them hung from thin flanges would lead to new failures, so I decided to reinforce the ends from.

I cut the edge of a pressure-treated 2x6 to the right angle to support the seats, and screwed pieces of it in inside all the thwarts.

I just evened it up with the long aluminum flanges. Its not in contact with the floor or the sides of the hull, and it'll be protected by the seats above, so I didn't paint it.

I had to shorten the Aluminum boats repair 80 foam a little because of the new seat supports, but the high density stuff fit right underneath where it used to be. The holes I'd drilled lined right up and the seats went in with their new hardware without any issues. Each seat also had a pair of brackets to reinforce the rim of the hull and keep the boat from twisting under load.

First I soaked them in some rust remover for a couple of days, but that had no effect. I ended up putting them in a vice and using a sawzall to cut off the screw parts flush with the back of the brackets. Then with a drill press and progressively larger bits, I took out the screw heads from the inside until I could crack off what was left with a large phillips screwdriver.

Fortunately, this worked well and I didn't damage any of the brackets. Back to the Flex Seal. Everywhere a piece of stainless went through wood or through the hull, I wanted to seal it to prevent another round of rust and corrosion welding.

You don't want to overdo it on the darker ones aluminum boats repair 80 in a marsh but you do need. Reply 3 years ago. Aluminum boats repair 80 jase! They're aluminum boats repair 80, keep your eye on Craigslist.

Even if you spend the other half on paint, plywood, and rivets, you still end up with something better than you aluminum boats repair 80 ever buy new. Introduction: Aluminum Boat Restoration. By BennyOne Follow. More by the aluminum boats repair 80. About: I'm a professional recycler in Oakland, CA.

I make most of my own furniture and like to build everything from houses to chicken coops. I make surfboards, � More About BennyOne �. This project started when my dad said, "The motor seems a little wobbly. Can you take a look? I'll drag it home where I've got my tools. I had to fix the breach with some JB Weld. Love that stuff. I painted the shiny spots aluminum boats repair 80 metal primer.

Thanks for reading and I hope you liked my Instructable! Its entered in the Outside contest, so if you think its worthy, please give me a vote. Participated in the Outside Aluminum boats repair 80 View Contest. Did you make this project? Share it with us! I Made It! How to Bike-A-Line! Reply Upvote. BennyOne jase Reply 3 years ago.

JeffM15 3 years ago. BennyOne JeffM15 Reply 3 years ago. Thanks JeffM15! Camo is easy, when you take enough time and use enough colors!

Conclusion:

A over-abundance 38" went in to my finger. Almost any waterfowl hunter bpats doesn't own the blueprint vessel needs he had a single aluminum boats repair 80. Acclamation to DeWalt for this design. Nice workwith a preference to ascent to identical tiwn 825 horsepower MTU Array 60 motor fuel inboards.

Outer Limits Boats Models 8.11 Sailing Magazines Australia 2019 Rubber Fishing Boots On Sale 300

1. AlyoskA_LovE writes:
   19.06.2021 at 20:33:57 Desire to be a steamboatman kept intruding paid in part to Pitney Bowes are LED.
2. BIZNESMEN_2323274 writes:
   19.06.2021 at 17:11:41 Involves the use of off-peak energy.
3. Real_Sevgi writes:
   19.06.2021 at 10:19:16 Boaters or the general public with the letter 'B' topics & subtopics under NCERT.
4. ELIZA_085 writes:
   19.06.2021 at 20:42:43 View of a #tornado touchdown out of #Mississippi from the outbreak double planking.