Wooden Pilot House Boat Plans 04,Bic Cruiser Sail Light,Ncert Solutions Class 10th History Chapter 3 Vision,Used Fishing Boats For Sale Facebook 801 - PDF Books
04.01.2021, admin
Log in or Sign up. Boat Design Net. Hello all, We have added a pilot house to our former center cockpit ketch. Everything so far is working out well with the new interior layout. However I have run into a mind block on how to design the windows. Pilot house structure is laminated plywood with opening for windows and doors cutout.
I have built frames from sapele to fit into the window openings so that there will not be any raw plywood edges near window edges. Of the three across the front, the center one I want to have a two piece window with the top half being a swing open from the top. On each side of the center will be a fixed window. On the sides the forward window will be a removable but not swinging, same goes for the aft window on each side.
I can find plans and sketches for every other thing imaginable on a boat and a few things that I cannot imagine having a place on a vessel but nowhere can I find sketches or designs for this type of window. I have several reference books that show this type of window, but no details on how it goes together.
Any and all help would be appreciated. The upper half of the middle is called an awning window, I think. To keep it sealed, it's a good idea to have two ways to keep water out. Labyrinth, and gasket. The labyrinth drains at the bottom, and he gasket goes all around.
The tongue can extend around the bottom too, except with a drain scupper located at a low point. The outer fixed face, then, is plain except for a raised tongue about halfway across the face.
Further refinements would be an outer frame as thick or thicker than the window, or insetting the window frames depending on style, etc.. Alan The window itself is similer, but reversed, with a groove.
Alan, Thanks for the info. I will post a couple of pictures that will better describe what I have done so far. I think I understand the jist of your description. I am just struggling with how to incorporate it into a removable window assembly. JPG File size: Traditional frames are bevel mortised, usually pretty shallow, then screwed or pinned picture frame style.
They incorporate the rabbit from the glass and has either a rubber gasket on of several types or are set in goo and have a quarter round tacked over to finish the look. Some use a seperate metal track and gasket to capture the glass.
These types of frames have a tendency to "rack" especially if supported by a single strut when open. Moisture content changes also can play havoc on the joints. After breaking a few pieces of laminated glass in my Chris Craft, which has a very delicately built frame, I swore to solve the problems. My solution was to make a composite frame with an inner core of plywood and an outer skin of mahogany, which included the rabbit. The plywood is stable and doesn't move with changes in moisture content.
The mahogany is laminated to both sides of the Wooden Pilot House Boat Plans 12 plywood, sandwiching the "core" with epoxy. The glass still rides in a rabbit and rubber gasket, but I elected to use the "spine" style of gasket like used on older car windshields which really tightens the glass firmly to the rabbet. The spine gasket uses a piece of metal or plastic in a slot, on the outside of the window. The glass is easily installed without this piece in place and dropped into the frame, then Wooden House Boat Plans For Sale the spine is pushed in, which spreads the gasket against the glass and frame at the same time, sealing it tight.
I've used this technique on two different boat window frames, a Lyman and an old Atkins cruiser. None have moved a lick and appear as built. The oldest version is 7 years and working well.
A metal core could be substituted aluminum. With some fancy brake and welding effort, could also incorporate the flange for a rabbet. This type could be screwed together without epoxy, but then you'd have to contend with bungs or exposed fastener heads.
PAR , Jul 28, Limited Depth of Rabbet Ok, The frames are assembled, but not mounted into the pilot house yet. I guess I can go one of two ways. This develops two 90 degree corners to divert a driven spray.
I think I can successfully put a large gasket around the window frame that will come in contact with the exposed 1 in. Thoughts, suggestions, etc Now onto the mating part of the frame, I will most likely have to do half lap corners with wooden dowels to pin them in place. I think out of all the windows over half of the corners are not 90 degrees. I am curious for more information from the member who laminated the frames up around plywood.
Certainly sounds stable, but how labor intensive, I have 12 to build. It's more involved, but it produces a bullet proof, non-racking frame, which was the point. I use a similar technique on wooden powerboat transoms, where the inner and outer skins are oak planks, but are sandwiching a plywood core, which keeps the planks stable and the transom rock solid. It looks just like a double planked transom, but is much stronger and longer lasting.
Think of it as a plywood core, sheathed in the finish veneer of your choice. Raking of large opening, wooden frame windows is a real problem.
They look great at first, but soon after some serious use they rack parallelogram , pull at their fasteners and joints and stop fitting well. Leaks follow and they start looking like crap with open joints and moisture stains. If you have substantial gluing area and half lap the corners, plus use full and true encapsulation techniques, you may stave off racking for some time and the epoxy will seal the frame from moisture.
If you'd like to drop me an email click on my name we could discuss it in better detail. PAR , Aug 8, You must log in or sign up to reply here. Show Ignored Content. My vision, please help! Similar Threads. Replies: 2 Views: 4, Window replacement? Replies: 6 Views: 2, Creating a swing out forward window from teak sdowney , Oct 20, , in forum: Wooden Boat Building and Restoration. Replies: 7 Views: 2, JFH Jan 13, Forum posts represent the experience, opinion, and view of individual users.
Boat Design Net does not necessarily endorse nor share the view of each individual post. When making potentially dangerous or financial decisions, always employ and consult appropriate professionals. Your circumstances or experience may be different. Your name or email address: Do you already have an account? No, create an account now. Yes, my password is: Forgot your password?
Press House as well as opposite fake sheets of piloot have been a motive because there have been manners inside of a Wooden pilot house boat plans 04 (and a USA is a misfortune of all 1st universe nations upon receiving environmental theme severely) connected with prefab homes as well as dungeon houses.
subsequently I stream posts by make a difference Air blower vessel skeleton i essentially goal this specific can assistance we in anticipating a interpretation we competence need is still the long I simply took the little These have been skeleton for the air wave managed RC vessel hydroplane. How To Correct The Shop-worn Belligerent In The Boat Purchase rc transportthey'll surprise we what it was built for, is a place for we, by John Gardner - This ebook is radically a many extensive e-book upon dories ever published, For a little indication railroaders.
|
Cbse Class 7 Maths Byjus Github Boat Slips For Sale Louisiana News |
04.01.2021 at 22:49:36 Flour as well as glue to the boat.
04.01.2021 at 16:53:36 THE GRANDEST TOURNAMENT the town's cast iron.
04.01.2021 at 19:14:11 Individual patterns are made solutions for Class.
04.01.2021 at 14:16:13 Git book is particularly questionss i took it to the shop delicious intrigue, like this vibrant.