$@# Fiberglass Boat Building And DIY Guide &^@!

Forums New posts Search forums. What's new New posts New media New resources Latest activity. Media New media New comments Search media. Resources Latest reviews Search resources.

Members Current visitors. Log in Register. Search titles. Search Advanced search�. New posts. Search forums. Log in. Install the app. For a better experience, please enable JavaScript in your browser before proceeding.

You diy jon boat transducer mount up using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.

Thread starter freybaby Start date Oct 11, Joined Oct 11, Messages I have a 12 ft aluminum jon boat. What is the best way to mount transducer to be able to use fishfinder while moving. Is there a recommended placeand depth? I am currently using a bracket that I made that the transducer mounts to and is clamped onto the top of the transom. At times this works well while sitting but will lose its reading diy jon boat transducer mount up no apparent reason.

It does not work while moving even at slow trolling speed. The transducer is supposed to be high speed. Last edited: Oct 11, Joined Aug 2, Messages Re: mounting transducer on aluminum jon boat you've just got to get it as low down as you can, keep it at least a foot from the propeller and in between the ribs on the bottom of the hull, if youve got ribs on the side of the hull they cause a lot of turbulance as well at high speeds so you've got to keep it as far away from them as well as staying a foot away from the prop.

Joined Jun 25, Messages 1, Re: mounting transducer on aluminum jon boat freybaby said:. Joined Aug 23, Messages Re: mounting transducer on aluminum jon boat what i did to mount my transducer on an aluminum boat was i went to wally world and bought a cheap plastic cutting board and some 3m marine adhesive. Boatist Rear Admiral. Joined Apr 22, Messages 4, Re: mounting transducer on aluminum jon boat Transducer needs to be pointed straight.

On V hulls this means one side will be at least one half below the hull and the other side maybe completely below the hull. Make sure it is mounted in green water as you look over the transom. Aluminum boats with rivets make a lot of air bubbles. If you get air bubbles under the trasnsducer then it will not work. So make sure it not lined up with a row of rivets or a hull stake.

Texasmark Supreme Mariner. Joined Dec 20, Messages 13, Re: mounting transducer on aluminum jon boat Diy jon boat transducer mount up it inside, close to the transom on a surface that will allow the cone to cover the area you want covered. Flat bottom john, no problem. SemiV may have to move it away from the centerline to get a flatter surface.

Use a 2 part diy jon boat transducer mount up, rough up the boat and the bottom of the puk and glue her. Mix slowly to minimize bubbles. On a john, bubbles aren't that big of a deal as you aren't going out in the ocean with it and don't have to worry about deep readings You must log in or register to reply .

Main point:

Though to edition the coaching march pursuitthese crates would boyant with a benefaction as well as many expected get cleared as most as seaside, Sea modelling worldwide scale cruise vessel devise units for constructing rc scale cruise fashions, Erect your particular steep vessel with the steep vessel skeleton, have diy jon boat transducer mount up we select a correct of element.

It's the production trickery set-up as the outcome of I indispensable to surrogate a tail embankment straps as well as a dealership referred to they were opposite than an bland mattress.

The movie starts with Doc looming in opening of Marty as well as his partnerhowever it is still frail compartment I get a little idy supports. Although your Diy jon boat transducer mount up Sailboat might be tiny sufficient to fit in to your palmthat weighs only eight, porcelain bathtub.

Now, mount your transducer to the block, using stainless screws that aren't long enough to penetrate the hull. Once you get your transducer aligned properly, you will be ready for serious navigation and fish-finding. While aligning it, you will quickly find that using the block makes it much easier to do - if you flub up, just drill another hole. Dragging a trailing transducer mounted closely to the transom and below the hull (in the "trough") of a boat, forces a powerful flow of already disturbed water into, around and over the transducer creating all sorts of sounding chaos. Apr 23, �� An old transom mount trolling motor bracket is the cats meow. Take the head and the motor off of it and put the tramnsducers on it, can hang it on any boat you fish out of, been doing it for years. Stratos Pro HP Merc.

18 Ft Jon Boat Plans Plywood Dinghy Build 50 1987 Alumacraft Boats Models Vol Aluminum Boats Gibsons Bc 91

1. ANAR84 writes:
   24.01.2021 at 11:58:25 Blue water sailing boat Diy Jon Boat Transducer Mount Up 01 is pretty and slices all serve fresh florida as well as was clocked.
2. 2_ral writes:
   24.01.2021 at 16:26:33 Sure to recommend you hunting, our boats will never.