Build Your Own Floating Boat Dock Pdf,10 Class Ka Math Ka Question Answer Amazon,Small Boat Sailing Vessel Size - Videos Download
24.05.2021, adminThe old boat dock had seen better days. As the water rose, so did the dock, all the way above the tops of the dock piles. The old deck had to go, and the EHT crew built a new one. Shown here is the basic plan for the swimming dock. Figure not drawn build your own floating boat dock pdf scale.
Our plans were for a byfoot dock to serve primarily as a swim platform throughout summer until the old boat dock could be demolished and rebuilt.
The owner of build your own floating boat dock pdf lake property ordered a flotation kit online that consisted of six dock floats. These inch thick 2-byfoot floats are each foam-filled with expanded polystyrene but have a seamlessly molded outer shell made of extra strong polyethylene, containing ultraviolet inhibitors.
A dock must also withstand the rigors of Mother Nature, and she throws a lot at a wooden structure that floats on water. Decks are supposed to remain still, but docks must be built strong enough to shoulder all the extra stress. The type of framing and decking material is also an important consideration. Ecolife is build your own floating boat dock pdf treated lumber that is protected with a non-metallic preservative plus a wood stabilizer, offering the natural beauty of real wood combined with dimensional stability and weathering protection.
This reduces cracking,checking, warping and splitting. Plus, the treatment is no more corrosive to fasteners and metal fittings than untreated wood. However, even with build your own floating boat dock pdf preservative treatment, applying a waterproof sealant to the wood will provide the best protection. The lake house sits on a considerable slope, so we had to carefully plot our plan of attack.
The kwn, most construction-friendly area to build the project was the relatively level and flat driveway. However, the driveway was nearly 50 yards from the lake, and we were building a byfoot dock. If we were to build the whole thing on the driveway, we would not be able to lift it to the water.
So, we compromised. We constructed this deck in phases to carefully manage the weight of the structure. We began construction on the relatively flat driveway to keep the rim-joist frame as square and level as possible. To ensure a flat, level frame on which everything else would be built, we assembled the four rim build your own floating boat dock pdf on the driveway.
The 2-by-8 rim joists comprised the outside perimeter of the dock. We centered each of the plates mid-height of the joists, and we found that it helps to clamp the plates in position while you drill the holes for the bolts. You can always tighten the nuts and bolts with a socket wrench, but we used a powered impact wrench that saved us hours of labor. When fooating, it is critical that each rim joist is square and level so take any means necessary to make sure this happens.
We used everything from scrap lumber to landscape pavers as shims floatting keep the frame in shape while we fastened the four corners.
Once the square perimeter of rim joists was complete, we carried the dock frame closer to the lake onto a paver patio where we installed the interior joists. When building a dock such as the one shown, there are two things to consider when determining joist placement: 1 the size of your deck boards, and 2 the mounting locations of your flotation devices. Full 2-by deck boards can be installed over joists spaced oninch centers.
First, we measured the distance between the mounting holes on the dock floats, and fastened the corresponding joists so they exactly matched the spacing of mounting locations. Once psf critical joists were installed, we located the remaining joists 16 inches from their centers.
The dock joists install with heavy-duty plates and through-bolts as. It helps to clamp the hardware in place while you drill the bolt holes.
Make sure to locate the joists so they match the mounting holes of the flotation devices. Like the rim joists, the deck joists were installed with a combination of lag bolts, nuts, washers and galvanized plates. The plates include an L-bracket to fasten the joists to the rim lumber, as well as two smaller plates that sandwich the joists to the bracket.
The hardware provides a solid and secure connection that resists tension and twisting within the dock frame. To provide some extra structural integrity, we cut blocking from 2-by-8 material and fastened the blocks build your own floating boat dock pdf the center joists of the dock that would not be bridged by the flotation devices.
Notice the old storm-wrecked dock in the background�the motivation for this project. With all the joists assembled, the dock had accumulated a great deal of weight. At this point our team of five Extreme How-To staff members carried the completed dock frame even closer to the lake, where we attached the six flotation devices to the joists.
The flotation units added even more weight to the structure,and the dock was upside-down. We needed to flip over the build your own floating boat dock pdf to have the floats on the. To do so, we recruited a Jeep with a front-mounted winch. Once flipped, the dock was roughly 8 feet from the water in preparation of launch.
The winch was critical to manage the heavy weight of the structure. We needed to install at least some of the deck boards overland to provide a working platform on which to install the remainder of the decking on the water. We fastened each deck board with stainless steel deck screws from GRK Fasteners, two per joist. Driving the fasteners with an impact driver proved to be the quickest method of installing the decking.
For bowed boards, we used the board-straightening BowWrench from Cepco Tool, which clamps over a joist to leverage the bowed board in straight alignment bot the installed decking www. A BowWrench is a handy tool to straighten bowed decking boards. At the time of construction floatimg water level was low, so rather build your own floating boat dock pdf sliding the dock easily into the water, we had to make the transition over the sheer ledge of a 3-foot seawall.
This was an awkward affair in which we used 2-by-8 boards as makeshift ramps and the winch to keep the weight of the dock manageable as we eased it into the water. Once in the water, we completed the remainder of the decking. The property had two piers. One was home to the build your own floating boat dock pdf older dock, the other was a narrow, shorter fishing pier that would serve as the gangway to the new dock.
These heavy-duty, L-shaped galvanized brackets required eight through-bolts and washers. To mount the platform to the gangway, we bowt two heavy-duty brackets called Chain Pile Holders, which we bolted to the rim joist and floatung last row of decking. To center doc dock on the pier, build your own floating boat dock pdf measured between the two posts that would hold the dock in place.
The center of the posts had a inchspan. Sixteen bolts and washers later, the Chain Pile Holders were in place. We paddled the dock over to the posts and wrapped them with the chains to anchor the dock in place.
The chains fit loosely around the piles,keeping the dock in place but providing enough slack so they can slide easily up and down the posts as the water level rises and falls. The chains of the Chain Pile Holders loosely wrap thegangway piles, allowing the dock to move with changes in the water level. The final phase of the dock project was to add vinyl docktrim to the three edges that were not connected to the pier supplied by TaylorMade Products, www.
The trim package starts with 6-byinch vinyl corner bumpers, which we top-fastened to the deck with the stainless steel GRK screws. The trim strips that fit between the flozting bumpers are called dock bumpers, and we used a hacksaw and snips to trim them each to fit flush between the corner pieces.
The bumpers are manufactured with a tough PVC inner core that is surrounded with kwn white vinyl, providing a cushion for boats, jet skis and people climbing up the side of the dock. Like the corner trim, the bumpers fasten to the top of the dock with stainless screws and provide a crisp, finished look to the new dock.
The final step build your own floating boat dock pdf to install the vinyl dock trim. With a team of five guys firing on all pistons, we managed to complete the bui,d and send it swimming despite its heavy weight. It was tough work, osn we wrapped up the day with cold beverages and barbecue ribs and now have a new place for build your own floating boat dock pdf in the sun.
These epoxy resins are VOC free, low [�]. Bkild process rejuvenates the wood. The drying oils stay at the surface, lock in the conditioning oils and create Build Your Own Floating Boat Dock Quiz a dry to [�]. Free Newsletter Signup Enter e-mail address to subscribe and get latest updates and info. The drying oils stay at youg surface, lock in the conditioning oils and create a dry to [�] More Info.
You should know:Twenty-fourview. The organisation can additionally be upheld by the repository about Lego trains called Railbricks, a single which floats aloft in a H2O. We might do with handling your hyperlinks the bit improved - it seems similar to the spammy thing has crept in .
Go to the Adobe site at www. All rights reserved. Prices shown are in U. Dollars and do not include freight, applicable federal, state or local taxes, customs duties or export packing charges. Prices, specifications and availability of items are subject to change without notice. The Complete Marine Construction Warehouse. Search DockBuilders. Working with Documents from this Site.
How do I download these documents for use on my hard drive? Having problems printing? Request Catalog. Contact Us. Site Map. Cleats, eye bolts, and other accessories are great dock accents as well. Check out more pics at www. What are the alternatives to pressure treated wood in a project like this? Can't use any materials that leach chemicals as pond is our drinking water source.
Thanks in advance. Great dock! Reply 5 years ago. We built a similar floating dock but used recycled galvanized fence posts for the piers. We were able to drive these into the lake bottom just using a post driving tool which can be found at any hardware store. Clearly not as heavy duty as this but we have gone through a lot of winter storms and they have done well.
The pilings that are around the outside of the pier are usually done by a private contractor that uses a counter weighted pile driver on a floating barge to drive the pilings into the lake or riverbed. Assembly all necessary tools and materials required. Did you make this project? Share it with us! I Made It! How to Bike-A-Line! How to Make a Stock Tank Pool! Reply Upvote. ProFloat 4 years ago. How did you get the pilings in the bottom of the lake?
Huge sledgehammer? Two Paddles Design zenfunk Reply 5 years ago.
|
Pontoon Boat Prices Zone Fishing Boats For Sale Erie Pa France Byjus Class 7 Maths Chapter 2 Ed |
24.05.2021 at 12:14:29 Always improving, as these small but mighty machines need sandpaper to epoxy spray paint for ads based.
24.05.2021 at 14:57:53 We compiled a list cost up to $ for a one hour you will.
24.05.2021 at 23:17:20 Anniversary Roughneck The 25th Anniversary Roughneck combines some of the.